2018 Kel-Berg T100 Alloy Aggregate Tipping Trailer
2018 used Kel-Berg alloy aggregate tipping trailer.
High tensile lightweight steel chassis.
Chassis finished in Red & Body finished in Silver
Single Alloy sides.
3 Metre rear wear plate 14mm thick.
Air operated auto rear door.
- In Stock
- Hydro Clear sheeting system
- ALCOA Duro bright rims
- PM1155 On-board weigh system
- Body finished in Silver
|Make / Model||
Kel-Berg T100 29 m3 Pressed aluminium aggregate body on steel chassis
Overall length: 10:035 mm, king pin position: 750 mm, neck depth: 200 mm, chassis main rail centres: 1300 mm, king pin to centre of rear axle: 8050 mm.
The full length I beam chassis and cross members are constructed from high tensile steels. This total chassis system increase the torsional strength and flexibility whilst keeping the centre of gravity low and reducing the tare weight for increased productivity. Swing up anodised aluminium side guards are secured on galvanised bolt on stays, the retractable rear under run bar is finished in RAL 9010 white, both these items are easily changed if damage.
SAF INTRADISC plus INTEGRAL 9 ton on/off road use, The INTERGRAL is a two-piece brake disc that is manufactured by compound casting from different materials, which is gentler on the material prolonging the service lift of the pads and disc.
The suspension systems are the relevant axle manufactures own, although each system has raise and lower valve with auto reset ride height & auto drop front lifting axle.
A two line pressure system with standard C couplings mounted on the front of the chassis. KNORR-BREMSE 4S2M EBS / ABS, incorporating RSP anti roll, load sensing valve, park & shunt buttons mounted on the side of the chassis.
24 Volt electrics are fitted with two 7 pin ISO and one ABS / EBS sockets fitted to front of trailer on galvanised brackets. Loom system housed in plastic tubing. HELLA Easy Conn light system fitted which has plug wiring connections which are specially developed for the 24V trailer application to ensure a long lasting and reliable system, 2 x LED front markers, LED amber side marker lights mounted to the chassis to C&U regulations, LED rear end outline maker lights 2 off per side & HELLA 3 chamber lights mounted on rear galvanised light board finished in RAL 9010 White.
|Wheels & Tyres:||
10 stud spigot steel wheel rims 11.75 x 2.5, fitted with six off premium 385/65R22.5 tyres.
6 off 180 degree heavy duty black thermos plastic wings with Kel-Berg logo flaps on the rear axle.
JOST Low maintenance 2 speed legs with rocker feet, finished in black.
Internal length: 9575 mm, internal height: 1450 mm, internal width: 2440 Cubic capacity: 29 3m 38 yards
The shape of the Kel-Berg single piece pressed aluminium aggregate body was designed to give the operator a body capable of carrying a range of materials also to help prevent products sticking inside when the load is discharged. The angled front bulkhead enables most of the tipping forces to be directed down through the king pin to the tractor unit rather than along the trailer chassis causing it to bow upward. The body is designed and constructed using specially designed top and bottom extruded aluminium rails, this gives the body its extraordinary strength and rigidity. Bevelled edges are incorporated into the top rail to stop any material remaining on it after loading has taken place. Floor thickness: 7mm with additional 7mm reinforced wear plate on the last 3 metres of body giving a 14 mm in total, side wall thickness: 5 mm.
The tailgate is angled forward to ensure it meets the edge of the body which extends 10 mm from the rear frame with momentum to ensure any material is removed enabling the door to close against the rubber seal creating a water tight seal. The tailgate has a fully air automated locking system which is energised when the body is lifted off the chassis, there is also has a manual button located on the chassis. The hinges are located 200 mm forward on the top rail which enables the door to pivot allowing maximum aperture for quicker and easier load discharge. A set of manual cattle clamps are provided which are located on each side.
The Edbro tipping cylinder is mid mounted to the front bulkhead and finished in the colour of the chassis. The rear tipping is the full width of the chassis and the hinges are located on the outer edge at distance of 1700 mm centres which contributes to improved stability during tipping. The discharge angle is 49 degrees
The chassis and body come with 2 years against structural defects The tipping gear has a full 3 years The Daw-barn Hydro clear sheeting system has 2 years